Eden Wt 800 Service Manual
Download PDF file with EDEN WT-800 Owner's Manual. Available translations: EN. Have You lost manual for Your appliance? Come visit us, We have largest library of. Free download of Eden WT800 User Manual. Troubleshooting help from experts and users. Ask our large community for support. Eden Electronics Operation Manual. Forward Congratulations on your purchase of the Eden WT -550 Traveler Bass. Must be adapted by a service tech for U.S.
. World Tour Bass Guitar Amplifier Covering Model WT800 (B Version) THE LEADER IN BASS AMPLIFICATION. The Eden World Tour products group is the result of our quest for ultimate bass tone and maximum reliability.
Telezapper
Cabinets
Your amplifier was designed, engineered and manufactured equivalent to aircraft vibration standards and housed in a one-piece aluminum case with steel top to ensure maximum reliability. The Eden line of World Tour amplifiers is the result of our research and development in combining high performance and compact size. Just as a skilled craftsman needs good quality tools that won't let him down on the job, so does a good musician. We hope you enjoy the tool we’ve created for you. If you experience any discomfort or ringing in the ears or suspect hearing loss, you should consult an audiologist. Thank you for your purchase of an Eden bass guitar product.
This unit has been designed and constructed to give you years of trouble-free service. FRONT PANEL FEATURES Input Jack – Designed to accept a standard inch mono phone plug. For best results use a high quality shielded cable to connect your instrument to the amplifier. The input is buffered and will handle standard passive, high level active, and piezo input signals.
In all other modes of operation, this feature is defeated. Mono Bridge Switch – Engages Bridge Mono Operation. To engage, push the switch IN. Mono Bridge Indicator – Lights to show that the amp is in Bridge Mono mode. EXTREMELY IMPORTANT NOTE: Do NOT engage Mono Bridge in combination with bi-amp operation. When connecting this cabinet to the WT800B in Bridge Mode, it will receive approximately 1000 Watts RMS, which is a near-perfect match. Left/High Amp Output – These consist of two inch jacks and an NL-4 connector (sometimes called a Speakon).
The jacks are wired in parallel. The total speaker load impedance should not go below 2 ohms. Do not use fast blow fuses. To convert your amplifier from US to European fusing, remove the Fuse Holder and insert a 5 Amp slow blow fuse.
Flip the fuse holder over and reinsert. IMPORTANT NOTE: In order to operate properly in other parts of the world, your amplifier may require minor modifications.
Level – Controls the level being sent from the XLR balanced output jack. We suggest setting the control at approximately 12 o’clock initially. If the signal to the board is too hot, it’s better to engage the Input Pad on your channel of the board than to turn it down here, if at all possible. Right/Low Amp Output – These consist of two inch jacks and an NL-4 connector (sometimes called a Speakon). The jacks are wired in parallel. The total speaker load impedance should not go below 2 ohms. On NL-4 connectors, we use +1, -1 connections.
Mono Bridge Output. The total impedance of all speakers connected to each of the amplifiers should not exceed 2 Ohms. Make sure that the Bi-amp and Bridge Mono switches are both OFF. In the OFF position, both switches should be flush with the face of the amplifier. &/or speakers. We’re serious about this.
Pay attention. GETTING A GREAT TONE As bassists, each of us has in our head a concept of our perfect sound. Eden amplifiers are designed to help you easily achieve the sound you hear inside.
In order to ensure the ultimate in tone, it’s important to follow the procedure outlined below. Don’t skip steps; don’t jump around. Yes, this may take a minute or two, but the work is well worth it. Once they’ve done it a few times, most users can do it time and again in about a minute. Once you have properly set your Input Gain, turn the Master Volume up to a comfortable listening level and proceed with the rest of the setup process. Setting the Compressor - If you want to use compression, engage it now by turning the Compressor Defeat switch OFF. If EQ clipping occurs, you can either decrease the boost or decrease the Input Gain.
Remember, too, that our EQ controls are active, and are meant to turn both ways – not just UP! This means that you can enhance a certain frequency spectrum either by boosting that frequency or by cutting the adjacent frequencies. (apparent) tone, especially in the mids and high end. ANOTHER NOTE: If you are using Dual Mono or Bi-Amp operation, you can use the Balance control to adjust the balance between different cabinet models to achieve your sound. There you have it: a quick and easy process to help you get the perfect tone from your Eden amplifier. As previously mentioned, it make take a few extra minutes the first few times you go through this, especially if you take the time to experiment with all the knobs and switches, which we highly recommend.
Balance control all the way to that amp. MAINTENANCE Your Eden amplifier has been designed to require minimal routine maintenance. Attention to the following areas will ensure optimum performance of your amplifier. We’re serious. Don’t blow this off, OK? Contact Point Cleaning –.
DO NOT continue to use the amplifier in this condition. Learn More – If you’d like to learn more about your amplifier (or about our company and its activities), we invite you to visit our website – www.eden- electronics.com.
There you’ll find articles to help you better understand our products and the technical stuff some people find so interesting. (847) 949-8444(fax) Eden Note for those who care: This manual was written by David (Eden) Nordschow, Eden’s Chief Propellerhead & Master of All Things Technical, and Lane Baldwin, Eden’s Special Projects Coordinator (Many Other Functions).
Eden Wt800 Schematic
Any grammar errors are David and Lane’s fault, as are the attempts at humor. My Favorite Settings Setting 1 Setting 2 Setting 3 Setting 4.
The Eden has a thermostatically controlled fan, my first thought is to clean the fan and airways and make sure it is working properly. This relates to some heat problems on solid state stuff. If they get too hot, some shut off for protection, the fan should automatically speed up on this model to compensate. When volume is low watch the fan. Also, make sure the impedance switch is set properly. I've very rarely seen any reason to use 2ohms settings.
The only way to run that is with 2 4ohm cabinets in parallel. If they are in series it would become 8ohm. Any other way will make the amp get too hot on 2 ohm setting. Most cabs are 4, 8, and 16. Mar 05, 2013. Here is your schematic for the power amp.
There is a separate amp for the tweeter using a LM3886 which is fairly well protected. Open the unit and test the tweeter driver. Scroll down to 'Get Manual' and click on it to download the schematic. At the site is also the preamp section as a separate schematic. You probably don't need that for the failure you are seeing.
A lot of the tweeter drivers seem to get blown up, but once you test you will be able to find if the problem is in the amp or the driver. May 03, 2011.